Water Damage Restoration Cost in Temecula, CA
Last updated
- What most homeowners pay
- $1,200–$5,000
- Hourly restoration labor
- $70–$200
- Typical after-hours fee
- $50–$200
- Low end, a toilet overflow
- $350
Typical Costs
How Much Does Water Damage Restoration Cost?
Water damage restoration in Temecula typically costs $1,200–$5,000, and the average job runs about $3,000 (Fixr, 2025). That covers extraction, drying and minor repairs. A small clean-water job can cost a few hundred dollars, while sewage or structural damage runs far higher.
The Type of Water
Clean water from a supply line runs about $3.75–$4.25 per square foot to extract and dry. Water from a toilet, drain or storm is contaminated and runs $7.00–$7.50, because more has to be removed and disinfected.
How Far It Spread
One wet room costs far less than water that ran under cabinets, into closets and up the walls. Carpet and drywall dry quickly, while hardwood, plaster and concrete hold water much longer.
How Long It Sat
The EPA advises drying within 24 to 48 hours. After that, mold can start and swollen materials can’t be saved, which turns a drying job into a rebuild.
These are national figures from Fixr (2025), Thumbtack, Today’s Homeowner and Bob Vila, and no source shows a California premium. They are typical ranges, not quotes. The price for your home depends on what an inspection finds, and you get it in writing before any work begins.
Cost by Job
Water Damage Costs by Type of Job
Each kind of water damage involves different work, so each has its own typical range. By room, a flooded bathroom runs $500–$4,500 and a kitchen $1,750–$8,000, because kitchens have more cabinets and flooring (Fixr).
- 01
Water Extraction
About $3.75–$4.25 per square foot to extract clean water, or $150–$500 per room to pull water out of carpet and pad (Fixr, Thumbtack).
- 02
Burst Pipe Water Damage
Typically $1,000–$4,000 to dry out and repair the damage a burst pipe leaves behind, separate from the plumbing repair itself (Today’s Homeowner).
- 03
Slab Leak Water Damage
Finding the leak runs $100–$400 and repairing it $1,000–$4,000, before drying and any flooring that has to be replaced (Fixr).
- 04
Water Heater Leak
A new heater runs $900–$3,000 installed, plus drying the garage floor and the wall behind the tank (Fixr).
- 05
Sewage Backup Cleanup
Usually $2,000–$10,000 in total, because soaked materials are removed and every surface the sewage touched is disinfected (Bob Vila).
- 06
Flood Cleanup
Storm water is priced as contaminated, at about $7.00–$7.50 per square foot, plus removal of soaked drywall and insulation (Fixr).
- 07
Water Damage Repair
Drywall repairs typically total $300–$800, and a water-damaged ceiling runs $325–$1,100 once the area is dry (Bob Vila, Fixr).
Need a Real Number?
Get a Written Estimate for Your Home
Ranges only go so far. Call and describe the damage, and a restoration crew can inspect your home and quote the work before anything starts.
Keep the Cost Down
How to Keep Water Damage Costs Down
Stop the Water at the Main
Close the valve where the supply line enters the house. Every gallon that doesn’t spread is drywall and flooring that stays.
Start Drying Within 48 Hours
The EPA’s window is 24 to 48 hours. Drying inside it keeps the job at the low end of the range and mold out of the bill.
Photograph Everything
Shoot each room, the source and the waterline. A well-documented claim is easier for your insurer to approve in full.
Get the Estimate in Writing
Ask for a written estimate before work starts, and keep the moisture readings. Both support your insurance claim.
$3.75–$4.25
Per sq ft, clean water from a supply line
$4.10–$6.50
Per sq ft, gray water from a washer
$7.00–$7.50
Per sq ft, sewage or floodwater
$1.50–$3
Per sq ft to repair drywall
National figures from Fixr (2025) for extraction and drying, before repairs.
- To acknowledge
- 15 days
- To accept or deny
- 40 days
Insurance
Does Insurance Pay for Water Damage Restoration?
Often, but it depends on where the water came from and how long it ran. Here’s how most California policies treat the cost.
Usually Covered
Sudden water from inside the home, like a burst supply line or a failed water heater, including the extraction, drying and repairs.
Often Excluded
Slow leaks that ran for weeks and the mold that follows. Flood needs its own policy, and sewer backup needs an add-on.
What Your Insurer Needs
Photos, the written estimate and the crew’s moisture readings. Together they show what was damaged and what the work costs.
Cost by Class
Water Mitigation Cost by Damage Class
Restoration crews rate every job from Class 1 to Class 4 by how much is wet and what it soaked into. The class is one of the biggest drivers of the price (Fixr, 2025).
Class 1, $150–$400
A small area with little water absorbed, like a spill on tile or one corner of carpet that’s caught right away.
Class 2, $500–$1,000
A whole room is wet, with the carpet and pad soaked and water wicking less than two feet up the walls.
Class 3, $1,000–$3,000
Most of the area is soaked, often from above, through the ceiling, walls, insulation, carpet and subfloor.
Class 4, $20,000–$100,000
Water is held in hardwood, plaster, concrete or stone, which needs specialty drying that runs much longer.
Cost Questions
Questions About Water Damage Costs
Most homeowners pay $1,200–$5,000 for extraction, drying and minor repairs, and the average is about $3,000 (Fixr, 2025). Contaminated water, damage that spread through several rooms or mold can push a job well past that.
About $3.75–$4.25 per square foot for clean water, $4.10–$6.50 for gray water and $7.00–$7.50 for sewage or floodwater, for extraction and drying (Fixr, 2025). Repairs are priced on top, with drywall at about $1.50–$3 per square foot.
Typically $325–$1,100 (Fixr), depending on how much drywall has to be replaced and the texture to match. A ceiling should only be repaired once the leak is fixed and moisture readings show it’s dry.
A typical floor repair runs $200–$2,000, and a damaged subfloor section $250–$750 (Fixr). Replacing water-damaged carpet runs about $4.75–$10.50 per square foot, depending on the carpet you choose.
Usually not. The plumbing repair is a separate job done by a plumber. A slab leak, for example, typically costs $100–$400 to find and $1,000–$4,000 to repair, or up to $4,000–$15,000 if the line is rerouted (Fixr).
Mold remediation typically runs $1,500–$9,000 on its own (Fixr). The best way to avoid it is drying the home within 24 to 48 hours, as the EPA advises.
Only a rough one. Online calculators multiply square footage by an average rate, but they can’t see water inside walls or under flooring. An accurate price needs an inspection with moisture meters, which shows where the water actually went and what has to come out.
For a small clean-water spill caught right away, towels, a wet vacuum and fans may be enough. Once water reaches carpet pad, the inside of a wall or the subfloor, hidden moisture can turn into mold and a bigger bill later.
Want a Real Number?
Find Out What Your Repair Will Cost
Call and describe the damage. A restoration crew can inspect your home, measure where the water went and give you a written estimate before any work begins.
What Happens Next
- 1You describe the damage and where it started
- 2The crew checks every wet area with moisture meters
- 3You approve a written quote before work starts
- 4Water extraction and drying begin